• DCC vorbereitet (Schnittstelle vorhanden)

Small data and label variations Operating LED front and rear tricolor flush-mounted with raised gasket class lights** Black cab armrest Raised slug electrical conduit cover on rear walkway deck with slug electrical bus connections on end Fully-assembled Multiple road numbers Operating LED ground lights on both sides of locomotive* Printed and LED lighted number boards* Extended walkway duct (SP toolbox) on left side Front and rear full width multiple unit (MU) hose catch tray 3-hose multiple unit (MU) hose clusters with silver gladhands Semi-scale coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Straight uncoupling levers with loop handles front and rear and four inner and two outer mounting brackets Notched pilot faces without lifting holes or slots Deck mounted multiple unit (MU) receptacle "Tall" stepwells with see-through steps Front and rear early small deck extension Handrail set with inward facing end rail mounting brackets and chain Standard front and rear drop steps Scale sectioned treadplate detail on walkways Rectangle walkway lights mounted between sandbox clean out doors (non-operating) 81” low short hood with ratchet handbrake with angled chain guard, “inverted” louvers on the left side, and round vent on top Bolted battery box doors with wide louvers SP “split” cab sub-base doors with stiffener rib and early hinges Standard EMD headlight in short hood Dash 2 cab with 11-bolt (top and bottom) window panels, modified (“used-to-be”) SP L-window, large armrests, and “inverted” hot water heater louvers on right front Detailed cab interior with separate floor, rear wall, seats, and standard AAR control stand Vent on rear cab door, cab front above engineer’s window, and large square vent on cab roof on fireman’s side Sliding cab side windows Tall clear wind wings mounted fore and aft of cab side window on both sides of cab Standard EMD sunshades and long sunshade tracks Lost wax brass cast Nathan P-3 (P24R1 configuration) horn on number board housing “Whip” antenna mounted to center of cab roof Accurate hood door and long hood detail Early electrical cabinet "zig-zag" seam, further from rear of cab Early “stand-off” ECAFB Intermediate inertial air intake grills with top drip rail Dual tall exhaust stacks Accurately profiled extended-range dynamic brakes without batten strip See-through dynamic brake intakes with resistor grid detail Square PAF (Paper Air Filter) housing “Chicken-wire” radiator intake grilles See-through standard 48” radiator fan housings with fan blades visible inside Curved radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, early center axle snubbers, sanding lines and brackets, and D-77 traction motor and air duct details, triple clasp brake shoes, and third brake cylinder Dimensionally accurate truck centers Speed recorder mounted to first axle left front Rearward facing handbrake chain mount for HTC trucks Tall jacking pads with holes (early) Aft engineer’s side sidesill notch Tab-mount EFCO Tripod-mount bell with air line on cab roof Salem air filter (accordion style) 4,000-gallon fuel tank with fuel fillers and dual vertical gauges and vertical breather pipe Factory-applied wire grab irons, wire lift rings, windshield wipers, trainline hoses with silver gladhands, sand hatch covers, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 70, 83 and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22”

Produktgewicht inkl. Verpackung: 1,320 kg

Angaben zur Produktsicherheit:
Hersteller: Scale Trains, 4901 Old Tasso Road NE Cleveland, TN 37312, USA, www.scaletrains.com
Verantwortlicher Importeur: RD-Hobby Modellbahnen, Jaegersburger Str. 17,68649 Gross-Rohrheim, Deutschland, email@RD-Hobby.de