Digitrax Easy Connect 8 Pin Plug to 8 pin DCC medium plug Motor & Function Decoder that fits many N and HO Scale Locos. 22.16mm x 10.28mm x 5.1mm •1.0 Amp/1.5 Amps Peak •6 FX3 Functions, 0.5 Amp •Digitrax Easy Connect 8 Pin Plug to 8 pin DCC medium plug. •Works with PX112-6F Power Xtender.

BXP88 makes adding detection and transponding to your layout easier than ever. No more complicated wiring! •DCC Occupancy Detection supports up to 8 Detection Sections letting you know when equipped rolling stock is in a detection section on your layout. •One Transponding Zone per Detection Section lets you know the location of transponder-equipped locos or rolling stock. •Intelligent Automatic short-circuit and over-current power management for each Detection Section, improves reliability by avoiding most booster fault shutdowns. •Connects to LocoNet to transmit Detection Section occupancy, Transponding and track power information. •Detects any powered locomotives in a Detection Section. •Identify where specific rolling stock is on your layout with Digitrax transponder-equipped locos and rolling stock. •Detects rolling stock equipped with resistor wheel sets. •Plug and Play with Digitrax DCC systems with automatic Railsync polarity detection. •LED output headers for front panel indication of Detection Section occupancy, Transponding, and power status. •Easy-connect pluggable track wire terminal blocks can plug-in straight or at right angles. •3 Amp capacity per Detection Section , 8 Amp total unit capacity. •Automatically updates status at track power on. •Operations Mode Read Back allows you to read CV values of decoders equipped with transponders when on track. •Firmware update capability via IPL over LocoNet.

- For Intermountain N scale F7A & B units with wired motors produced after Jan 2014 - 6 FX3 Functions - 11.98mm x 54.99mm x 2.4 mm

Current Rating-Motor1.0 Amp/1.25 Amps PeakSize0.271” x 1.296” x .099” (6.8834mm x 32.9184mm x 25.146mm)InstallationBoard Replacement (show less) These decoders are made to fit specific locomtoive chassis. Locomotives that have circuit boards that can have decoders installed in place of the original circuit board are made by many manufacturers. In some cases, locomotive modifications, motor isolation and additional soldering may be required during installation of this type of decoder. Function leads can be added to these decoders using solder pads available on the decoder. See the instruction sheet for the particular decoder you are using for specific instructions. Sometimes these are called plug n' play or drop in decoders. Function Outputs2-500mAFunction TypeFX3 (read more) Current Rating-Motor1.0 Amp/1.25 Amps PeakSize0.271” x 1.296” x .099” (6.8834mm x 32.9184mm x 25.146mm)InstallationBoard Replacement (show less) These decoders are made to fit specific locomtoive chassis. Locomotives that have circuit boards that can have decoders installed in place of the original circuit board are made by many manufacturers. In some cases, locomotive modifications, motor isolation and additional soldering may be required during installation of this type of decoder. Function leads can be added to these decoders using solder pads available on the decoder. See the instruction sheet for the particular decoder you are using for specific instructions. Sometimes these are called plug n' play or drop in decoders. Function Outputs2-500mAFunction TypeFX3 (read more) Current Rating-Motor1.0 Amp/1.25 Amps PeakSize0.271” x 1.296” x .099” (6.8834mm x 32.9184mm x 25.146mm)InstallationBoard Replacement (show less) These decoders are made to fit specific locomtoive chassis. Locomotives that have circuit boards that can have decoders installed in place of the original circuit board are made by many manufacturers. In some cases, locomotive modifications, motor isolation and additional soldering may be required during installation of this type of decoder. Function leads can be added to these decoders using solder pads available on the decoder. See the instruction sheet for the particular decoder you are using for specific instructions. Sometimes these are called plug n' play or drop in decoders. Function Outputs2-500mA FeaturesSeries 3 (read more) FeaturesSeries 3 (read more)

Weitere Infos auf und Sounds zum downloaden: www.digitrax.com/sounddepot.php

The PR4 makes decoder programming and interfacing your layout and computer easier than ever. The PR4 seamlessly switches between computer interface and decoder programming modes automatically without having to press any buttons. The PR4 is electrically isolated between USB and LocoNet for added stability and protection. Packaged in a smaller footprint the PR4 offers all the same great features as the PR3 it replaces. Mit dem PR4 Decoder Programmer und SoundLoader Software, in Verbindung mit PC und Programmiergleis können Sie: - Sound nach Ihren Wünschen verändern - Sounds downloaden - testen - CVs umprogrammieren - SoundLoader Software zum Download auf der Digitrax Webseite Im Kit enhalten sind: - PR4 Programmer - USB Schnittstelle Benötigt wird: - 12-15V (DC) Gleichstrom Netzteil - PC mit Windows XP - Programmiergleis - Windows XP, Vista and 2000. - Mac OS 10.4/10.5 mit JMRI. Sounds von www.digitrax.com/sounddepot downloaden und mit dem Digitrax Programmer aufspielen: AC4400 SD38-2 F40PH GE Evolution Traction/Trolley SD70 Western Pacific #1983 British DMU Class 108 British Class 37 BritishLight-Prairie 2-6-2 44XX British �Yorkshire� switcher U33 RDC Bells and Whistles GP10 #7562 Union Pacific Challenger #3985 SW1 #4741 E8 Southern #6900 SW1C #4742 ALCO RS32 #30 Fairbanks Morse 1244 Switcher SD40-2 GP38 C44-9 weitere folgen in Kürze.

•For Intermountain N scale FT A units with motor contact "shoes" •6 FX3 Functions •.472” x 2.165” x .098” 11.98mm x 54.99mm x 2.4 mm •Replaces DN163I1A

- komplett mit Netzteil 220V, 3A - Anleitung in englischer Sprache

Zephyr Express gives you simple to use Digitrax Complete Train Control for a great price. It offers simplified advanced train operation for any size layout and is fully expandable. You won’t have to start over when you want to do more with your railroad. Zephyr Express Set Includes: •DCS52 All-In-One Throttle/Command Station/Booster to run your layout •PS314 Power supply to provide power to run your DCS52 •One LT1 LocoNet Cable & Decoder Test Kit •Zephyr Express Quickstart Guide •Zephyr Express Manual •Digitrax Decoder Manual Zephyr Express Offers: •Cost effective entry level LocoNet Compatible system •Color 2.4” LCD Screen. •Large Backlit Keypad. •Speed control knob and direction switch with brake. •Integrated USB Computer Interface •Easy 2 and 4 digit addressing. •Smooth speed control. Run multiple trains at once without blocking! •Run up to 20 addresses at the same time on your system. •Run up to 20 throttles at the same time on your system. Jump Ports for using DC power packs as additional throttles •Use one or two smooth DC power packs as throttles to control DCC equipped locomotives. •Simple, cost effective way to add more throttles to your Zephyr Express set. •Makes it easy to share the fun of DCC with layout visitors and young operators. •Functions on locos controlled by Jump throttles remain active. Over 9000 Locomotive Addresses •Use Address 00 to run one or more locos without DCC decoders •Two Digit Addressing is easy to use. (Address 01-127) •Four Digit Addressing-use the number painted on your engines as its address. 3.0 Amps of Power to run multiple trains. •Booster outputs 13V DC for safe operation in N and HO scales. Function Control •Control lights and sound with 29 functions (F0-F28) •Function 2 is a special non-latching key that can be used to sound the horn for as long as the key is held down. •Constant brightness lighting. Headlights can be directional or independently controlled (depending on decoder). Stationary Decoders, Turnout Control & Turnout Position Reporting •Access to stationary decoder control for turnouts and other devices. •Control 2000+ stationary decoder addresses. Consisting •Universal consisting, Digitrax preferred method. ALL locos can be consisted, even analog locos. •Advanced consisting, allows only advanced consist capable mobile decoders. •Basic consisting, program decoders to run on same address. Decoder Programming •Built in read/write programmer that can read and write all CVs. •Supports Direct programming (Digitrax preferred method). Also supports paged & register mode programming. •Operations mode programming can be used to program decoders on the layout. •Blast Mode Programming for Sound Expandability with Digitrax LocoNet •Use Zephyr Express as a starting point for your Digitrax LocoNet System, then add components. •Use Zephyr Express as an expansion set with Digitrax equipment you already have installed. •Add Radio or IR via LocoNet. Just plug-in a UR90, or UR92 receiver and add IR and/or Radio throttles. Comes Complete with DCS52 Command Station, PS314 Power Supply, LT1 LocoNet Cable and Decoder Tester, System Reference Manual and Decoder Manual.

scale FP7A and FP9A with motor contact "shoes" For Intermountain N scale FP7A and FP9A with motor contact "shoes" 6 FX3 Functions .472” x 2.165” x .098” 11.98mm x 54.99mm x 2.4 mm Replaces DN163I2

Fits Intermountain N Scale FP7A with wired motors produced after Jan 2014 6 FX3 Functions 472” x 2.165” x .098” 11.98mm x 54.99mm x 2.4mm

Grosser Handregler mit Farbdisplay und voller Programmier- möglichkeit und Infrarot-Fernbedienung, Handbuch in Englisch, 29 Funktionen. - Works with compatible LocoNet systems - Color 2.4” LCD Display Screen - Advanced menu system and displays - Built-in scrolling help and prompting - Soft ON/OFF switch, with zero OFF power-drain - Advanced display Power Saving for longer wireless battery operation - No more 9V batteries to remove! Throttles are now powered in wireless modes by 3 AA cells! - Can use recharged AA batteries - Available in standard tethered or Radio Duplex - Duplex Scan for available Networks and radio signal strength. Run without cords! - All throttles come with a LocoNet cord that can be unplugged, and is replaceable - Dual throttle controls let you control two locos simultaneously - Run locomotives with “encoder click” knobs for both speed and direction control - Full numeric keypad makes loco selection simple - Control light and sound effects functions with the press of a button - Control 29 functions (F0-F28). - Function active/inactive indicators - Convenient step-by-step throttle option set up - Supports simplified decoder programming - Simplified 2 or 4 digit addressing setup - Over 9,000 locomotive decoder addresses - Supports turnout and stationary decoder control - Over 2000 turnout decoder addresses - Fast clock display - Recall feature - Advanced Route editor

Grosser Handregler mitFarbdisplay und voller Programmier- möglichkeit und Funk-Fernbedienung, Handbuch in Englisch, 29 Funktionen. - Works with compatible LocoNet systems - Color 2.4” LCD Display Screen - Advanced menu system and displays - Built-in scrolling help and prompting - Soft ON/OFF switch, with zero OFF power-drain - Advanced display Power Saving for longer wireless battery operation - No more 9V batteries to remove! Throttles are now powered in wireless modes by 3 AA cells! - Can use recharged AA batteries - Available in standard tethered or Radio Duplex - Duplex Scan for available Networks and radio signal strength. Run without cords! - All throttles come with a LocoNet cord that can be unplugged, and is replaceable - Dual throttle controls let you control two locos simultaneously - Run locomotives with “encoder click” knobs for both speed and direction control - Full numeric keypad makes loco selection simple - Control light and sound effects functions with the press of a button - Control 29 functions (F0-F28). - Function active/inactive indicators - Convenient step-by-step throttle option set up - Supports simplified decoder programming - Simplified 2 or 4 digit addressing setup - Over 9,000 locomotive decoder addresses - Supports turnout and stationary decoder control - Over 2000 turnout decoder addresses - Fast clock display - Recall feature - Advanced Route editor - For “DCE”

Ersatzstecker schwarz für DB220

- komplett mit Netzteil

DCS210 Central Unit / Booster 8 A, DT602 Handregler mit 2.4” LCD Anzeige. Handbuch in Englisch, UP-5 Steckdose. PS615 Netzteil 14, 28, 128 Fahrstufen für jede Lok individuell einstellbar. Analoge Loks fahren auf Adresse 00. Das Set enthält: * DCS210 8A Command Station/Booster * DT602 Super LocoNet Handsteuergerät * UP5 Universal Panel * PS615 Netzteil The DT602 Advanced Super Throttle & DCS210+ Advanced Command Station Offers Works with compatible LocoNet systems Color 2.4” LCD Display Screen Advanced menu system and displays Built-in scrolling help and prompting Soft ON/OFF switch, with zero OFF power-drain Advanced display Power Saving for longer wireless battery operation No more 9V batteries to remove! Throttles are now powered in wireless modes by 3 AA cells! Can use recharged AA batteries Available in standard tethered or Radio Duplex Duplex Scan for available Networks and radio signal strength. Run without cords! All throttles come with a LocoNet cord that can be unplugged, and is replaceable Dual throttle controls let you control two locos simultaneously Run locomotives with “encoder click” knobs for both speed and direction control Full numeric keypad makes loco selection simple Control light and sound effects functions with the press of a button Control 29 functions (F0-F28). Function active/inactive indicators Convenient step-by-step throttle option set up Supports simplified decoder programming Simplified 2 or 4 digit addressing setup Over 9,000 locomotive decoder addresses Supports turnout and stationary decoder control Over 2000 turnout decoder addresses Fast clock display Recall feature Advanced Route editor USB Interface Big System Capacity for Big Layouts Run up to 100 addresses at the same time on your system. Run up to 100 throttles at the same time on your system. Over 9000 Locomotive Addresses Address 00 for operation of one loco or MU consist without decoders Two Digit Addressing is easy to use. (Address 01-127) Four Digit Addressing lets you use the road number of your engines as their addresses. (Address 0128-9000+) 5 or 8 Amps of Power to Run More Trains Selectable Scale Voltage for Safe Operation in ALL Scales Customizable Voltage Settings 5 amps of power with included PS615 power supply 8 amps with PS2012E power supply (sold separately) Function Control Control 29 functions (F0-F28). Function 2 is a special non-latching key that can be used to sound the horn for as long as the key is held down. Constant brightness lighting. Headlights can be directional or independently controlled (depending on decoder capabilities). Two DCC Outputs are Better than One! Use one output for programming decoders while the other runs the layout. No need to shut down the layout to program decoders! Use one output for a braking section while the other runs the layout. Decoder Programming Built in read/write programmer lets you program and read back CV values. Supports Paged programming (Digitrax preferred method). Also supports direct, register and ops mode programming Consisting Supports Universal consisting (Digitrax preferred method). Allows ALL locos to be consisted prototypically, even analog locos. Advanced consisting and Basic consisting, too! Nested consisting where consists can be consisted together. Stationary Decoders, Turnout Control & Turnout Position Reporting Access to stationary decoder control for turnouts and other devices. DT602 reports turnout position based on last command sent. Control 2000+ stationary decoder addresses. Routes Turnout List/Route capability to simplify complex yard operations. EZ routes button for simplified Command Station route programming Customizable System Options Turn audible warnings on or off. Set up purging options. Multi-format command station mode. Loco Reset button for easy system purging UP5 Universal Panel Makes LocoNet hook up simple! 2 LocoNet jacks for hooking up your LocoNet network. 3 throttle jacks for hooking up throttles and other non-RailSync devices. Expandability Evolution is just the beginning for large, complex layouts that emphasize prototypical operations. With LocoNet you can add more boosters, throttles, power management, detection, transponding, signaling and much more. DCS210+ comes with 3 LocoNet ports for easy expandability and a USB interface! Other Advanced Features IPL updatable firmware for continued product improvements Device Query and Device Statistics to help with troubleshooting Input Mode to help set up detection on your layout Uses Expanded slots

- komplett mit Netzteil

DCS-210 Central Unit / Booster 8 A, DT602D Funk- Handregler mit grosser Anzeige,Funksender eingebaut. Handbuch in Englisch, UR-93 Empänger. PS615 Netzteil. Analoge Loks fahren auf Adresse 00. Das Set enthält: * DCS210 8A Command Station/Booster * DT602D Super LocoNet Handsteuergerät (Funk- Betrieb möglich) * UR93 Universal Panel (Funk Empänger) * PS615 Netzteil für DCS210 * Netzteil für UR93 The DT602D Advanced Super Throttle & DCS210 Advanced Command Station Offers Works with compatible LocoNet systems Color 2.4” LCD Display Screen Full Duplex radio when paired with a UR92 or compatible Duplex Transceiver (sold separately) Advanced menu system and displays Built-in scrolling help and prompting Soft ON/OFF switch, with zero OFF power-drain Advanced display Power Saving for longer wireless battery operation Throttles are now powered in wireless modes by 3 AA cells! No more 9V batteries to remove! Can use recharged AA batteries Works in standard tethered, IR or Radio Duplex modes Duplex Scan for available Networks and radio signal strength. Run without cords! All throttles come with a LocoNet cord that can be unplugged, and is replaceable Dual throttle controls let you control two locos simultaneously Run locomotives with “encoder click” knobs for both speed and direction control Full numeric keypad makes loco selection simple Control light and sound effects functions with the press of a button Control 29 functions (F0-F28). Function active/inactive indicators Convenient step-by-step throttle option set up Supports simplified decoder programming Simplified 2 or 4 digit addressing setup Over 9,000 locomotive decoder addresses Supports turnout and stationary decoder control Over 2000 turnout decoder addresses Fast clock display Recall feature Advanced Route editor Big System Capacity for Big Layouts Run up to 100 addresses at the same time on your system. Run up to 100 throttles at the same time on your system. Over 9000 Locomotive Addresses Address 00 for operation of one loco or MU consist without decoders Two Digit Addressing is easy to use. (Address 01-127) Four Digit Addressing lets you use the road number of your engines as their addresses. (Address 0128-9000+) 5 or 8 Amps of Power to Run More Trains Selectable Scale Voltage for Safe Operation in ALL Scales Customizable Voltage Settings 5 amps of power with included PS615 power supply 8 amps with PS2012E power supply (sold separately) Function Control Control 29 functions (F0-F28). Function 2 is a special non-latching key that can be used to sound the horn for as long as the key is held down. Constant brightness lighting. Headlights can be directional or independently controlled (depending on decoder capabilities). Two DCC Outputs are Better than One! Use one output for programming decoders while the other runs the layout. No need to shut down the layout to program decoders! Use one output for a braking section while the other runs the layout. Decoder Programming Built in read/write programmer lets you program and read back CV values. Supports Paged programming (Digitrax preferred method). Also supports direct, register and ops mode programming Consisting Supports Universal consisting (Digitrax preferred method). Allows ALL locos to be consisted prototypically, even analog locos. Advanced consisting and Basic consisting, too! Nested consisting where consists can be consisted together. Stationary Decoders, Turnout Control & Turnout Position Reporting Access to stationary decoder control for turnouts and other devices. DT602 reports turnout position based on last command sent. Control 2000+ stationary decoder addresses. Routes Turnout List/Route capability to simplify complex yard operations. EZ routes button for simplified Command Station route programming Customizable System Options Turn audible warnings on or off. Set up purging options. Multi-format command station mode. Loco Reset button for easy system purging UR93 Duplex Radio Transceiver Panel Digitrax Duplex Radio Transceiver on LocoNet wire infrastructure (no IR support). More than double the radio range of UR92 Duplex units. Plug and Play setup, PS14 Universal power supply included. Compatible to be mixed with UR92 LocoNet Duplex Radio systems, for added coverage and reception. Status LEDS. Supports combinations of DT602D/DE and DT500D, DT400D and UT4D Duplex Radio throttles. UR93E available for countries that require EN-300-328 Wireless conformity. Expandability Evolution is just the beginning for large, complex layouts that emphasize prototypical operations. With LocoNet you can add more boosters, throttles, power management, detection, transponding, signaling and much more. DCS210+ comes with 3 LocoNet ports for easy expandability and a USB Interface! Other Advanced Features IPL updatable firmware for continued product improvements Device Query and Device Statistics to help with troubleshooting Input Mode to help set up detection on your layout Uses Expanded slots

Mit englischer Anleitung, Handregler mit Drehknopf Works with compatible LocoNet Systems Compact size for easy one-handed operation Color 1.5” LCD Display Screen Full numeric keys for easy locomotive selection Fine speed control with encoder knob Forward/Reverse toggle switch with braking On/Off Switch, uses AA or BP600MH batteries 2 or 4 Digit Locomotive decoder access, provide over 9,000 loco addresses 29 Functions Digitrax Infrared operation with UR90/91/92 Duplex wireless with UR93/92 Duplex Scanner and Duplex settings editor Over 2000 turnout decoder addresses Locomotive Recall feature Convenient Throttle Option Setup Detachable LocoNet cable and Lanyard For "DCE"

Mit englischer Anleitung, Handregler mit Drehknopf Works with compatible LocoNet Systems Compact size for easy one-handed operation Color 1.5” LCD Display Screen Full numeric keys for easy locomotive selection Fine speed control with encoder knob Forward/Reverse toggle switch with braking On/Off Switch, uses AA or BP600MH batteries The UT6 throttle integrates intuitive operation with rock solid design and low cost into a single hand held throttle featuring: - 2 or 4 Digit Locomotive decoder access, provide over - 9,000 loco addresses - 29 Functions - Digitrax Infrared operation with UR90/91/92 - Over 2000 turnout decoder addresses - Locomotive Recall feature - Convenient Throttle Option Setup - Detachable LocoNet cable and Lanyard - Replaces the UT4

Funkempfänger für Handregler DT602D/DE , DT500D, DT402D und UT4D. Funk-Empfänger für die drahtlose Steuerung Ihrer Züge mit entsprechend ausgerüsteten Handreglern, mit englischer Anleitung.

15 x 10mm

Vierfach Magnetartikeldecoder für ALLE Doppelspulen- (Märklin, Peco, Atlas, Roco usw.) oder Motorweichen (Feather, Tortoise usw.), Anleitung in Englisch. - Einfach zu installieren - Steuert 4 Weichen - für Weichen mit Motor- und Magnetantrieb - LocoNet Control - Stromaufnahme vom Gleis oder separater Booster - DCC Norm

Armaturenbretthalterung Schaltersteuergerät. Verdrahten Sie das DS74-Eingangskabel oder verwenden Sie DSXC4 für Plug-and-Play. Fascia mount Switch control device. Wire to DS74 input cable, or use DSXC4 for plug and play. Two color leds display current Switch state. Supplied with 3 wire control cable.