新商品! 到貨於 二月 2025

New roadname Era: 1993 to Early 2010s Series 7400 to 7499; Built 4-5/93 Road number 7477 Equipped with CSX and EJ&E Hoods, FRA-224 yellow conspicuity striping Fully-assembled Multiple road numbers Body with dual trough design and center divider, sixteen walkway side supports and simulated wood trough interior. Designed for the use of two hoods although, depending on the type of steel, the car can be run without hoods as well. Body has four wireform side grab irons and four wireform end grabirons 2 x Version 1 Hood: No corner reinforcement, long side handrail with grab irons, hood stacking brackets with outer extensions Each hood is constructed with up to 16 individual parts including six wireform handrails, four wireform grab irons, two hood stacking brackets, two hood top braces, and lifting bail Handbrake housing with finely detailed wheel and chain See-through photo-etched metal walkway Simulated wood interior floor using a hand applied wash Four (4) positionable load dividers Four (4) large die cast unwrapped coil steel loads Factory-applied end handrails, hood guides, stanchions, load divider tracks, metal grab irons, coupler cut levers, and trainline hoses with silver gladhands Complete underbody brake system with over 15 separately applied parts including air reservoir, control valve, and retainer valve plus wireform plumbing and trainline pipe with brackets Body-mounted semi-scale standard Type E knuckle couplers – Micro-Trains® compatible ASF Ride Control trucks with finely rendered raised foundry data 36” machined metal wheels Operates on Code 55, 70 and 80 rail Printing and lettering legible even under magnification Weighted to Industry standards for reliable operation Clear jewel box packaging safely stores model Minimum radius: 9 ¾” Recommended radius: 11”

• 與 DCC 解碼器
• 商品有聲音

Museum Qualität, noch mehr Details und Funktionen Das Set besteht aus A-Unit, B-Unit und Tender Alle Achsen angetrieben, Stromaufnahme über alle Achsen, LED Beleuchtung, Inneneinrichtung ESU LokSound + DCC Decoder Era: Late Mid 1960s to Late 1960s Series 1 to 15, built 2/59 Road number 6 3-unit set: “A”, “B”, and Fuel Tender Premium leather-like presentation case with metal latches for safe storage Fully-assembled Multiple road numbers available Printing and lettering legible under magnification Operates on Code 70, 83, and 100 rail Minimum radius: 18” without water and electrical bus connections and tender truck safety chain detail attached Recommended radius: 22” “A” Control Unit Without “Union Pacific” lettering on the nose Operating LED-lit tricolor (red, green, and white) class lights** Operating LED-lit cab interior light Operating LED-lit control panel Operating LED-lit ground light on engineer’s side Operating LED-lit rear walkway light Printed and LED lighted number boards With nose side grab irons Opening cab doors with separate door handles Detailed cab interior with separate control stand, floor, rear wall with water cooler, and seats Radiator mounted lost wax brass Leslie S-5T-R air horn mounted on clearance bracket Cab roof heater box with grille on right side only Square base whip antenna Large see-through photo-etched metal side grilles H – H dynamic brake housing with etched-metal grilles With air intake scoops Modified radiator with all-weather shutter Underbody frame rail with traction motor cable detail As delivered 2,500 Gallon diesel fuel tank Air tanks with separate plumbing Auxiliary reservoirs Rubber Multiple Unit (MU) and electrical bus connections between the “A” and “B” units Rubber water hoses between the “A” and “B” unit Durable metal semi-scale Type E knuckle couplers Factory-applied ladders, wire grab irons, coupler cut levers, windshield wipers, mirrors, trainline hose, lifting lugs, exhaust stack, bell, and sanding lines Highly detailed trucks with separately applied brake cylinders, air pipes and lost wax brass wheel slip indicators on left side frames Mixed SKF and Timken bearings on right side truck frames Chicago Pneumatic speed recorder on second axle right side Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pickup Directional LED headlight DCC & sound equipped locomotives feature: Operates on both DC and DCC layouts ESU LokSound 5 DCC & Sound decoder with “Full Throttle” feature Prime mover sound Curve squeal sound Frog clank sound Large oval speaker ESU designed “PowerPack” with two super capacitors*** DC/DCC & sound ready locomotives feature: Operable using a DC power pack DCC-ready with 21-pin connector “B” Turbine Unit Operating LED-lit back-up light Sliding engine compartment side doors Detailed interior with turbine visible inside Spinning turbine fan blade visible inside exhaust Dual Farr Dynavane inertial type air intake housings Single H dynamic brake housing with etched-metal grilles Offset air intake scoops With rear MU connections Factory-applied ladders, wire grab irons, coupler cut levers, trainline hose, lifting lugs, and sanding lines Underbody frame rail Highly detailed trucks with separately applied brake cylinders, air pipes and lost wax brass wheel slip indicators on left side frames Mixed SKF and Timken bearings on right side truck frames Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pickup DCC & sound equipped locomotives feature: Operates on both DC and DCC layouts ESU LokSound 5 DCC & Sound decoder with “Full Throttle” feature Turbine sound Curve squeal sound Frog clank sound Large oval speaker ESU designed “PowerPack” with two super capacitors*** 24C Fuel Tender 24,000-gallon capacity Welded seams Insulated Commonwealth 6-axle trucks Truck chains Factory-applied air tank, brake cylinder, and control valve Factory-applied multiple unit (MU) hoses Photo-etched metal tender deck walkway Operating LED-lit rear tender light

Prototype Specific ScaleTrains Multiple road numbers Fully assembled Finely cast stirrup steps; end details; underbody and brake system Wire grab irons Molded simulated wood deck Separately applied handbrake wheel Detailed die cast trucks 33” Machined metal wheels Accurately profiled .110″ wide wheel tread Plastic semi-scale Type E knuckle couplers, Kadee compatible Body mounted coupler box will accept Kadee whisker couplers Weighted to Industry standards Operates on Code 70, 83 and 100 rail Packaging safely stores model when assembled Minimum radius 18”

Prototypical ScaleTrains Walmart Inc./WAMU White with large "Walmart.com" lettering with Walmart ‘spark’ logo separating Walmart and com on container sides Era: Early 2000s to present Multiple road numbers available Fully assembled 53’ length high-cube height (9’, 6” tall) container 8-58-8 square side wall corrugations 7 corrugation front wall 1-3-1 door corrugations Weld bead and stacking point details Cored-through Inter-Box Connector (IBC) corner castings Four (4) separately applied door locking rods Separately-applied photo-etched metal hazmat placard holder Intricately decorated with rooftop reporting marks, warning labels and capacity data Stackable with our 53’ Reefer Container as well as most other brands of 53’ containers and chassis

• 與 DCC 解碼器
• 商品有聲音

Road Number Specific ScaleTrains Era: mid to late 1960’s appearance UP Series 1 to 15, built 2/1959 3-unit set: “A”, “B”, and Fuel Tender Fully-assembled Printing and lettering legible under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 11” Recommended radius: 19” “A” Control Unit Printed and LED lighted number boards Semi-scale Type E knuckle couplers With nose grab irons Detailed cab interior with control stand, floor, rear wall and seats Radiator mounted lost wax brass cast Leslie S-5T-R air horn mounted on clearance bracket Cab roof heater box Square base whip antenna Large see-through photo-etched metal side grilles H – H dynamic brake housing configuration With air intake scoops Modified radiator with all weather shutters Underbody frame rail As delivered 2,500 gallon diesel fuel tank Auxiliary reservoirs mounted to underside of fuel tank Two air tanks with separate plumbing Factory-applied ladders, wire grab irons, coupler cut levers, windshield wipers, mirrors, trainline hoses with silver glad hands, lifting lugs, exhaust stack, and bell Highly detailed trucks with separately applied brake cylinders, and air pipes; molded-on wheel slip indicators on left side frames and speed recorder on right side second axle Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pickup Directional LED headlight DCC & sound equipped locomotives feature: Operates on both DC and DCC layouts ESU LokSound 5 DCC & Sound decoder with “Full Throttle” feature Prime mover sound Single cub-type speaker DC/DCC & sound ready locomotives feature: Operable using a DC power pack DCC-ready with 21-pin connector “B” Turbine Unit Operating LED back-up light Dual Farr Dynavane inertial type air intake housings Single H dynamic brake housing Offset air intake scoops Blanked door panels and forward ventilation louvers Factory-applied ladders, wire grab irons, coupler cut levers, and trainline hoses with silver glad hands With rear MU connections Underbody frame rail Highly detailed trucks with separately applied brake cylinders, and air pipes; molded-on wheel slip indicators on left side frames Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pickup DCC & sound equipped locomotives feature: Operates on both DC and DCC layouts ESU LokSound 5 DCC & Sound decoder with “Full Throttle” feature Turbine sound Single cub-type speaker DC/DCC & sound ready locomotives feature: Operable using a DC power pack DCC-ready with 21-pin connector 24C Fuel Tender 24,000-gallon capacity Welded seams Insulated body Commonwealth 6-axle trucks Factory-applied air tank, brake cylinder, and control valve Factory-applied multiple unit (MU) hoses with silver gladhands Photo-etched metal tender deck walkway Operating LED rear tender light *Some sound and lighting functions are only operable using DCC

Road Number Specific ScaleTrains All-new model Era: 1969 to present Prototype examples in oxide red have been documented in service to present day TTJX series 80370 to 80519; built 12/69, 2/70-3/70 Fully-assembled Multiple road numbers Steel deck Transverse deck risers MacLean-Fogg tie-down details on deck Factory-applied metal grab irons, coupler cut levers, and trainline hoses and connection pipe with silver gladhands Early H-shaped jacking pads Vertical handbrake staff Complete underbody brake system with over 12 separately applied parts including air reservoir, control valve, reduction relay valve and retainer valve plus wireform plumbing and trainline pipe Body-mounted semi-scale standard Type E knuckle couplers – Micro-Trains® compatible ASF Ride Control trucks with finely rendered raised foundry data 36” machined metal wheels Operates on Code 55, 70 and 80 rail Printing and lettering legible even under magnification Paint colors match Tru-Color Paint color: TCP-093 Oxide Red Weighted to Industry standards for reliable operation Clear jewel box packaging safely stores model Minimum radius: 9 ¾” Recommended radius: 11”

Road Number Specific ScaleTrains All-new model Era: 1969 to present TTJX series 80370 to 80519; built 12/69, 2/70-3/70 Fully-assembled Multiple road numbers Steel deck Transverse deck risers MacLean-Fogg tie-down details on deck Factory-applied metal grab irons, coupler cut levers, and trainline hoses and connection pipe with silver gladhands Early H-shaped jacking pads Vertical handbrake staff Complete underbody brake system with over 12 separately applied parts including air reservoir, control valve, reduction relay valve and retainer valve plus wireform plumbing and trainline pipe Body-mounted semi-scale standard Type E knuckle couplers – Micro-Trains® compatible ASF Ride Control trucks with finely rendered raised foundry data 36” machined metal wheels Operates on Code 55, 70 and 80 rail Printing and lettering legible even under magnification Paint colors match Tru-Color Paint color: TCP-093 Oxide Red Weighted to Industry standards for reliable operation Clear jewel box packaging safely stores model Minimum radius: 9 ¾” Recommended radius: 11”

Road Number Specific ScaleTrains New road name Era: 1997 to present Series 242000 to 242236 Class G-110-90, built 10-12/97 Fully-assembled Multiple road numbers Early body type, built by Thrall: Thrall builder logos, heavy “H” shaped reinforcement on top of draft gear, and end handrails attached to hood ends Early V2 Hood: End handrails, round top lifting bail, inside guide stacking bracket and single reinforcement hood braces Hoods are constructed with 10 individual parts including four (4) wireform side grab irons, two (2) wireform end handrails, two (2) hood stacking brackets, two (2) hood reinforcement braces, and lifting bail Five (5) wrapped coil steel weight loads: two (2) small and three (3) medium Separate positionable coil steel load dividers Simulated wood interior floor using hand applied wash Body with four wireform side grab irons Factory-applied hood guides (4); brake wheel, stand, and chain; coupler cut levers (2); and trainline hoses (2) See-through photo-etched metal wrap-around walkway Complete underbody brake system with over 10 separately applied parts including air reservoir, control valve, retainer valve, and wireform plumbing ASF Ride Control trucks with finely rendered raised foundry data 36” machined metal wheels Body-mounted semi-scale standard Type E knuckle couplers – Micro-Trains® compatible Printing and lettering legible even under magnification Weighted to Industry standards for reliable operation Operates on Code 55 and 70 rail Clear jewel box packaging safely stores model Minimum radius: 9 ¾” Recommended radius: 11”

Road Number Specific ScaleTrains New road name Era: 1997 to present Series 242000 to 242236 Class G-110-90, built 10-12/97 Fully-assembled Multiple road numbers Early body type, built by Thrall: Thrall builder logos, heavy “H” shaped reinforcement on top of draft gear, and end handrails attached to hood ends Early V2 Hood: End handrails, round top lifting bail, inside guide stacking bracket and single reinforcement hood braces Hoods are constructed with 10 individual parts including four (4) wireform side grab irons, two (2) wireform end handrails, two (2) hood stacking brackets, two (2) hood reinforcement braces, and lifting bail Five (5) wrapped coil steel weight loads: two (2) small and three (3) medium Separate positionable coil steel load dividers Simulated wood interior floor using hand applied wash Body with four wireform side grab irons Factory-applied hood guides (4); brake wheel, stand, and chain; coupler cut levers (2); and trainline hoses (2) See-through photo-etched metal wrap-around walkway Complete underbody brake system with over 10 separately applied parts including air reservoir, control valve, retainer valve, and wireform plumbing ASF Ride Control trucks with finely rendered raised foundry data 36” machined metal wheels Body-mounted semi-scale standard Type E knuckle couplers – Micro-Trains® compatible Printing and lettering legible even under magnification Weighted to Industry standards for reliable operation Operates on Code 55 and 70 rail Clear jewel box packaging safely stores model Minimum radius: 9 ¾” Recommended radius: 11”

White container with KLLM Transport Services prancing horse and Frozen Food Express logos Era: Early 2000s to present Multiple road numbers available Fully assembled 53’ length high-cube height (9’, 6” tall) container Weld bead and stacking point details Cored-through Inter-Box Connector (IBC) corner castings Four (4) separately applied door locking rods Intricately decorated with rooftop reporting marks, warning labels and capacity data Stackable with most other brands of 53’ containers and chassis

• 與 DCC 解碼器
• 商品有聲音

Road Number Specific ScaleTrains All-new model Era: Mid 1990s – Early 2000s UP Series mixed, built 2-3/78 (ex-SP Series 8357 - 837) Road numbers 4425 (ex-SP 8361) and 4429 (ex-SP 8371) Data label and lettering placement variations Plated over front and blanked rear red LED Pyle-National 17540 “UDE” Gyralites Blanked class lights with bolted plates front and rear Round walkway lights (non-operating) 123” “snoot” low short hood with wheel handbrake and round vent on top SP “split” cab sub-base doors with lift-off hinges Dash-2 cab with bolted side window panels, SP/SSW blue flag bracket, and modified “L” front window “Whip” radio antenna mounted on ground plane over dust bin and dual Locotrol antenna ground planes on cab roof with conduits Early electrical cabinet “zig-zag” seam, further from rear of cab Intermediate inertial air intake grills with top drip rail Extended-range dynamic brakes Front straight uncoupling levers with loop handles and two inner and two outer mounting brackets; angled rear uncoupling lever with four mounting brackets Fully-assembled Multiple road numbers Operating LED-illuminated front deck-mounted ditch lights* Printed and LED-illuminated number boards* Vapor Corp. cab roof HVAC Front late SP/UP-style pilot plow with MU hose doors and grab irons Front and rear 3-hose MU hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Front pilot anticlimber Scale sectioned treadplate detail on the walkways Front "tall" stepwells and rear “ladder” steps SP nose headlight package Cab front door with additional door lock at top of door Tall clear wind wings with angled top corners mounted fore and aft of cab side window on both sides of cab Rear cab side vent on left side Standard EMD sunshades and long sunshade tracks Lost-wax brass Leslie RS-3L-R three-chime horn on clearance bracket, relocated to long hood roof Welded ECAFB (late) Handrail set with anticlimber front and rear end railing with outward facing mounting brackets, “breakaway” inner stanchions and chain Notched pilot faces with high mounted angled lifting slots Pilot-face mounted MU receptacle Detailed cab interior with separate floor, rear wall, seats, and standard AAR control stand Accurate hood door and long hood detail See-through standard 48” dynamic brake fan housings with fan blades visible inside See-through radiator intake compartment Etched-metal radiator exhaust grills with radiator shutters visible underneath Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, early center axle snubbers, sanding lines and brackets (outboard only Speed recorder first axle, left side Four-hole SP jacking pads Spare knuckle holders on fuel tank near fuel filler Sill-mounted EFCO Standard air tanks 4,400 gallon fuel tank with reinforced tank edges where sides meet the tank ends, dual fuel fillers, dual vertical gauges, round gauge on stand and vertical breather pipe Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DCC & sound equipped locomotives also feature: ESU LokSound 5 DCC & Sound decoder with “Full Throttle” One (1) cube-type speaker EMD 16 Cylinder 645E3 prime mover Operates on both DC and DCC layouts

• 與DCC的使用（DCC接口）

Road Number Specific ScaleTrains All-new model Era: Mid 1990s – Early 2000s UP Series mixed, built 2-3/78 (ex-SP Series 8357 - 837) Road numbers 4425 (ex-SP 8361) and 4429 (ex-SP 8371) Data label and lettering placement variations Plated over front and blanked rear red LED Pyle-National 17540 “UDE” Gyralites Blanked class lights with bolted plates front and rear Round walkway lights (non-operating) 123” “snoot” low short hood with wheel handbrake and round vent on top SP “split” cab sub-base doors with lift-off hinges Dash-2 cab with bolted side window panels, SP/SSW blue flag bracket, and modified “L” front window “Whip” radio antenna mounted on ground plane over dust bin and dual Locotrol antenna ground planes on cab roof with conduits Early electrical cabinet “zig-zag” seam, further from rear of cab Intermediate inertial air intake grills with top drip rail Extended-range dynamic brakes Front straight uncoupling levers with loop handles and two inner and two outer mounting brackets; angled rear uncoupling lever with four mounting brackets Fully-assembled Multiple road numbers Operating LED-illuminated front deck-mounted ditch lights* Printed and LED-illuminated number boards* Vapor Corp. cab roof HVAC Front late SP/UP-style pilot plow with MU hose doors and grab irons Front and rear 3-hose MU hose clusters with silver gladhands Body mounted knuckle couplers; Micro-Trains® compatible Coupler box accepts Micro-Trains 1015/1016 couplers without modification Front pilot anticlimber Scale sectioned treadplate detail on the walkways Front "tall" stepwells and rear “ladder” steps SP nose headlight package Cab front door with additional door lock at top of door Tall clear wind wings with angled top corners mounted fore and aft of cab side window on both sides of cab Rear cab side vent on left side Standard EMD sunshades and long sunshade tracks Lost-wax brass Leslie RS-3L-R three-chime horn on clearance bracket, relocated to long hood roof Welded ECAFB (late) Handrail set with anticlimber front and rear end railing with outward facing mounting brackets, “breakaway” inner stanchions and chain Notched pilot faces with high mounted angled lifting slots Pilot-face mounted MU receptacle Detailed cab interior with separate floor, rear wall, seats, and standard AAR control stand Accurate hood door and long hood detail See-through standard 48” dynamic brake fan housings with fan blades visible inside See-through radiator intake compartment Etched-metal radiator exhaust grills with radiator shutters visible underneath Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, early center axle snubbers, sanding lines and brackets (outboard only Speed recorder first axle, left side Four-hole SP jacking pads Spare knuckle holders on fuel tank near fuel filler Sill-mounted EFCO Standard air tanks 4,400 gallon fuel tank with reinforced tank edges where sides meet the tank ends, dual fuel fillers, dual vertical gauges, round gauge on stand and vertical breather pipe Factory-applied wire grab irons, windshield wipers, trainline hoses with silver gladhands, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 55 and 80 rail Packaging safely stores model Minimum radius: 9 3/4” Recommended radius: 11” DC/DCC & sound ready locomotives also feature: Operates on DC layouts DCC ready with E24 connector

Road Number Specific ScaleTrains New road numbers Era: 2014 to present DPRX Series 259017 to 260016; built 7/14-12/14 Road numbers 259074, 259184, 259217, 259349, 259368, 259380, 259433, 259439, 259561, 259569, 259692, 259875 and unnumbered 1202 diesel placard Fully assembled Multiple road numbers Photo-etched metal head shields for realistic thin profile Separately-applied printed hazmat placards See-through top and end photo-etched metal Handbrake housing with finely detailed wheel and chain Precision injection-molded one-piece tank body with separate ends Standard full-height side ladders Finely detailed manway cover and protective housing Finely detailed tank saddles with defect card holders Sturdy metal anti-personnel rods Die-cast metal end frames Separately-applied metal corner and end sill grab irons Factory-applied metal grab irons, coupler cut levers, and trainline hoses with silver gladhands Underbody outlet valve and chain detail Brake plumbing with separate air reservoir, control valve, and retainer valve plus separately applied wireform plumbing including trainline pipe with brackets Semi-scale coupler boxes Durable body-mounted die-cast metal semi-scale SE Type double-shelf knuckle couplers Highly-detailed ASF Motion Control Super Service 110-ton trucks with rotating blue bearing caps and separate brake beam detail Printed reporting mark and road number on all four trucks 36” machined metal wheels with accurately profiled .110" wide wheel tread Operates on Code 70, 83 and 100 rail Printing and lettering legible even under magnification FRA-224 yellow conspicuity striping Unnumbered cars available to create longer unit trains Decal sheet with number jumble available separately for unnumbered cars Weighted to Industry standards Packaging safely stores model Minimum radius: 18” Recommended radius: 22”

Road Number Specific ScaleTrains New road numbers Era: 2014 to present DPRX Series 259017 to 260016; built 7/14-12/14 Road numbers 259074, 259184, 259217, 259349, 259368, 259380, 259433, 259439, 259561, 259569, 259692, 259875 and unnumbered 1202 diesel placard Fully assembled Multiple road numbers Photo-etched metal head shields for realistic thin profile Separately-applied printed hazmat placards See-through top and end photo-etched metal Handbrake housing with finely detailed wheel and chain Precision injection-molded one-piece tank body with separate ends Standard full-height side ladders Finely detailed manway cover and protective housing Finely detailed tank saddles with defect card holders Sturdy metal anti-personnel rods Die-cast metal end frames Separately-applied metal corner and end sill grab irons Factory-applied metal grab irons, coupler cut levers, and trainline hoses with silver gladhands Underbody outlet valve and chain detail Brake plumbing with separate air reservoir, control valve, and retainer valve plus separately applied wireform plumbing including trainline pipe with brackets Semi-scale coupler boxes Durable body-mounted die-cast metal semi-scale SE Type double-shelf knuckle couplers Highly-detailed ASF Motion Control Super Service 110-ton trucks with rotating blue bearing caps and separate brake beam detail Printed reporting mark and road number on all four trucks 36” machined metal wheels with accurately profiled .110" wide wheel tread Operates on Code 70, 83 and 100 rail Printing and lettering legible even under magnification FRA-224 yellow conspicuity striping Unnumbered cars available to create longer unit trains Decal sheet with number jumble available separately for unnumbered cars Weighted to Industry standards Packaging safely stores model Minimum radius: 18” Recommended radius: 22”

Road Number Specific ScaleTrains New road numbers Era: 2014 to present DPRX Series 259017 to 260016; built 7/14-12/14 Road numbers 259074, 259184, 259217, 259349, 259368, 259380, 259433, 259439, 259561, 259569, 259692, 259875 and unnumbered 1202 diesel placard Fully assembled Multiple road numbers Photo-etched metal head shields for realistic thin profile Separately-applied printed hazmat placards See-through top and end photo-etched metal Handbrake housing with finely detailed wheel and chain Precision injection-molded one-piece tank body with separate ends Standard full-height side ladders Finely detailed manway cover and protective housing Finely detailed tank saddles with defect card holders Sturdy metal anti-personnel rods Die-cast metal end frames Separately-applied metal corner and end sill grab irons Factory-applied metal grab irons, coupler cut levers, and trainline hoses with silver gladhands Underbody outlet valve and chain detail Brake plumbing with separate air reservoir, control valve, and retainer valve plus separately applied wireform plumbing including trainline pipe with brackets Semi-scale coupler boxes Durable body-mounted die-cast metal semi-scale SE Type double-shelf knuckle couplers Highly-detailed ASF Motion Control Super Service 110-ton trucks with rotating blue bearing caps and separate brake beam detail Printed reporting mark and road number on all four trucks 36” machined metal wheels with accurately profiled .110" wide wheel tread Operates on Code 70, 83 and 100 rail Printing and lettering legible even under magnification FRA-224 yellow conspicuity striping Unnumbered cars available to create longer unit trains Decal sheet with number jumble available separately for unnumbered cars Weighted to Industry standards Packaging safely stores model Minimum radius: 18” Recommended radius: 22”

Road Number Specific ScaleTrains New road numbers Era: 2014 to present DPRX Series 259017 to 260016; built 7/14-12/14 Road numbers 259074, 259184, 259217, 259349, 259368, 259380, 259433, 259439, 259561, 259569, 259692, 259875 and unnumbered 1202 diesel placard Fully assembled Multiple road numbers Photo-etched metal head shields for realistic thin profile Separately-applied printed hazmat placards See-through top and end photo-etched metal Handbrake housing with finely detailed wheel and chain Precision injection-molded one-piece tank body with separate ends Standard full-height side ladders Finely detailed manway cover and protective housing Finely detailed tank saddles with defect card holders Sturdy metal anti-personnel rods Die-cast metal end frames Separately-applied metal corner and end sill grab irons Factory-applied metal grab irons, coupler cut levers, and trainline hoses with silver gladhands Underbody outlet valve and chain detail Brake plumbing with separate air reservoir, control valve, and retainer valve plus separately applied wireform plumbing including trainline pipe with brackets Semi-scale coupler boxes Durable body-mounted die-cast metal semi-scale SE Type double-shelf knuckle couplers Highly-detailed ASF Motion Control Super Service 110-ton trucks with rotating blue bearing caps and separate brake beam detail Printed reporting mark and road number on all four trucks 36” machined metal wheels with accurately profiled .110" wide wheel tread Operates on Code 70, 83 and 100 rail Printing and lettering legible even under magnification FRA-224 yellow conspicuity striping Unnumbered cars available to create longer unit trains Decal sheet with number jumble available separately for unnumbered cars Weighted to Industry standards Packaging safely stores model Minimum radius: 18” Recommended radius: 22”

Road Number Specific ScaleTrains New road numbers Era: 2014 to present DPRX Series 259017 to 260016; built 7/14-12/14 Road numbers 259074, 259184, 259217, 259349, 259368, 259380, 259433, 259439, 259561, 259569, 259692, 259875 and unnumbered 1202 diesel placard Fully assembled Multiple road numbers Photo-etched metal head shields for realistic thin profile Separately-applied printed hazmat placards See-through top and end photo-etched metal Handbrake housing with finely detailed wheel and chain Precision injection-molded one-piece tank body with separate ends Standard full-height side ladders Finely detailed manway cover and protective housing Finely detailed tank saddles with defect card holders Sturdy metal anti-personnel rods Die-cast metal end frames Separately-applied metal corner and end sill grab irons Factory-applied metal grab irons, coupler cut levers, and trainline hoses with silver gladhands Underbody outlet valve and chain detail Brake plumbing with separate air reservoir, control valve, and retainer valve plus separately applied wireform plumbing including trainline pipe with brackets Semi-scale coupler boxes Durable body-mounted die-cast metal semi-scale SE Type double-shelf knuckle couplers Highly-detailed ASF Motion Control Super Service 110-ton trucks with rotating blue bearing caps and separate brake beam detail Printed reporting mark and road number on all four trucks 36” machined metal wheels with accurately profiled .110" wide wheel tread Operates on Code 70, 83 and 100 rail Printing and lettering legible even under magnification FRA-224 yellow conspicuity striping Unnumbered cars available to create longer unit trains Decal sheet with number jumble available separately for unnumbered cars Weighted to Industry standards Packaging safely stores model Minimum radius: 18” Recommended radius: 22”

Road Number Specific ScaleTrains New road numbers Era: 2014 to present DPRX Series 259017 to 260016; built 7/14-12/14 Road numbers 259074, 259184, 259217, 259349, 259368, 259380, 259433, 259439, 259561, 259569, 259692, 259875 and unnumbered 1202 diesel placard Fully assembled Multiple road numbers Photo-etched metal head shields for realistic thin profile Separately-applied printed hazmat placards See-through top and end photo-etched metal Handbrake housing with finely detailed wheel and chain Precision injection-molded one-piece tank body with separate ends Standard full-height side ladders Finely detailed manway cover and protective housing Finely detailed tank saddles with defect card holders Sturdy metal anti-personnel rods Die-cast metal end frames Separately-applied metal corner and end sill grab irons Factory-applied metal grab irons, coupler cut levers, and trainline hoses with silver gladhands Underbody outlet valve and chain detail Brake plumbing with separate air reservoir, control valve, and retainer valve plus separately applied wireform plumbing including trainline pipe with brackets Semi-scale coupler boxes Durable body-mounted die-cast metal semi-scale SE Type double-shelf knuckle couplers Highly-detailed ASF Motion Control Super Service 110-ton trucks with rotating blue bearing caps and separate brake beam detail Printed reporting mark and road number on all four trucks 36” machined metal wheels with accurately profiled .110" wide wheel tread Operates on Code 70, 83 and 100 rail Printing and lettering legible even under magnification FRA-224 yellow conspicuity striping Unnumbered cars available to create longer unit trains Decal sheet with number jumble available separately for unnumbered cars Weighted to Industry standards Packaging safely stores model Minimum radius: 18” Recommended radius: 22”

• 與 DCC 解碼器
• 商品有聲音

Road Number Specific ScaleTrains New paint scheme Era: 1966 to early 1970s Santa Fe Series 1830-1889; built 10-12:66, Phase Ib1 Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-Illuminated rectangular walkway lights mounted between front and rear sanding valve doors and round walkway light, aft of raised walkway duct* LED-lit tricolor (red, green, and white) flush-mounted class lights with raised gasket** Front and rear full-width MU catch trays with footboards Front and rear early small deck extension Pivoting front and rear drop steps “Short” stepwells with see-through steps “Early” (“X”) pattern walkway treadplate Latched battery box doors with narrow louvers Latched cab sub-base doors with early hinges 81” low short hood with plated-over handbrake location Standard EMD high headlight in numberboard housing Early straight grabs and “flipped” nut-bolt-washer (NBW) mounting on nose front and top “35-Line” cab with standard front windshields Small mirrors mounted fore of cab side windows on both sides of cab No sunshades No Arm rests No cab vents Lost-wax brass Leslie RS-3L-R three-chime horn; mounted center rear of number board housing Can type antenna mounted on dust bin Standard electrical cabinet seam and bolted alternator door No ECAFB Early (smooth) blower duct housing Standard-height dust bin Standard-height exhaust stack Early (short forward taper) extended-range dynamic brakes “Chickenwire” radiator intake grilles with diamond-pattern mesh screens Standard-height fan housings Photoetched spiral-ring grilles with center disk Long walkway duct with three short stanchions Front and rear straight uncoupling levers with four brackets Handrail set with pilot face mounted outer end rail stanchions 4-hose MU hose clusters with silver gladhands Early (angled) deck-mounted MU receptacle Short “nub-bottom” pilot face Pilot face bracing detail behind stepwells Pilot face grab iron with inner mounting points Tall jacking pads with holes Sill-mount EFCO button Frame-mounted bell Salem air filter (accordion style) 4,000-gallon fuel tank with single fuel filler, single vertical fuel gauge, and round dial fuel gauge per side Detailed Flexicoil-C (low-mount brake cylinder) trucks with Hyatt bearing caps and sanding lines and brackets Speed recorder second axle, left side Factory-applied wire grab irons, wire lift rings, windshield wipers, trainline hoses with silver gladhands, sand hatch covers, and much more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible even under magnification Operates on Code 70, 83 and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DCC & sound equipped locomotives also feature: ESU LokSound 5 DCC & Sound decoder with “Full Throttle” functions Two (2) cube-type speakers Turbocharged EMD 20 Cylinder 645E3 prime mover ESU designed “PowerPack” with two super capacitors*** Operates on both DC and DCC layouts

Road Number Specific ScaleTrains Era: 2007 to present BNSF Series 793810 to 794112; built 6-10:2014 Fully-assembled Multiple road numbers With FRA conspicuity striping 82’ 7711 cubic foot smooth side body 12’ plug door with recessed tops section and separate door rods and door handle Carrier HVAC unit Square Refrigeration unit fuel tank Intricate A end refrigeration unit access platform with photo-etched metal platform deck Fuel tank end cage with separate plastic frame and wire grabirons Ribbed Roof Underbody brake rigging and components located specifically to match the 7711 cubic foot car Factory-applied ladders, metal grab irons, tack boards, coupler cut levers, and trainline hoses with silver gladhands Brake wheel, stand, and chain Brake plumbing with separate air reservoir, control valve, and retainer valve plus separately applied wireform plumbing including trainline pipe with brackets Photo-etched stainless-steel see-through Morton (stamped round hole) coupler crossover platform on B end of car Semi-scale coupler boxes Durable body-mounted die-cast metal semi-scale lower shelf Type E couplers Highly-detailed ASF Family of Trucks (FOT) 100-ton trucks with finely rendered raised foundry data; rotating black Timken three-sided bearing caps; separate “truck-mounted brake” brake beams; and side bearing detail Printed reporting mark and road number on all four trucks 36” machined metal wheels with accurately profiled .110” wide wheel tread Operates on Code 70, 83 and 100 rail Printing and lettering legible even under magnification Weighted to Industry standards for reliable operation Packaging safely stores model Minimum radius: 22” Recommended radius: 24”