新商品! 到貨於 二月 2025

預定截止日期：2024/6/24

• 與DCC的使用（DCC接口）

New road numbers Era: 1986 to mid 1990s Rio Grande series 5386 to 5397, built 8:1978 Fully-assembled Multiple road numbers LED-illuminated ground lights on both sides of locomotive* LED-illuminated-Illuminated rectangular walkway lights mounted between front and rear sanding valve doors and round walkway light, aft of raised walkway duct* LED-illuminated box-mounted Pyle-National 20585 Gyralite signal light in low short hood* LED-illuminated front and rear stand-off tri-color class lights** Printed number boards with separately controlled backlit LED-illumination* Directional LED headlights “McCarty” type re-rail frogs Front EMD-style low pilot plow without MU hose doors and grab irons Front and rear 3-hose MU hose clusters with silver gladhands Front late small deck extension Late front drop step (“fixed”) Front "tall" stepwells with see-through steps and rear “ladder” steps 88” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges Standard EMD headlight in numberboard housing Dash-2 cab with bolted side window panels and D&RGW blue flag bracket Detailed cab interior with separate floor, rear wall, seats, and standard AAR control stand Original cab front door Sliding cab side windows Standard Mirror mounted fore of cab side windows, both sides Rear cab side vent on left side Standard EMD sunshades and long sunshade tracks Lost-wax brass Nathan AirChime P24R1 (“P-3”) three-chime horn, center rear of number board housing Large Sinclair Excalibur “ice skate” antenna (communications) and small wedge antenna mounted on cab roof Early electrical cabinet "zig-zag" seam, further from rear of cab Welded ECAFB (late) Intermediate inertial air intake grills with top drip rail Extended-range dynamic brake Front straight uncoupling levers with loop handles and two inner and two outer mounting brackets Straight rear uncoupling lever with four mounting brackets Handrail set with inward facing end rail mounting brackets and chain; break-away stanchions on both ends Handrail ends and step faces painted white Front and rear 3-hose MU hose clusters with silver gladhands Semi-scale coupler buffer equipped with ScaleTrains.com durable metal semi-scale E Type knuckle couplers Notched pilot faces with high mounted angled lifting slots Pilot-face mounted MU receptacle "Tall" stepwells with see-through steps Front late small deck extension rear full-width front pilot anticlimber Scale sectioned treadplate detail on walkways Accurate hood door and long hood detail Standard turbo exhaust stack See-through dynamic brake intakes with resistor grid detail See-through standard 48” dynamic brake fan housings with fan blades visible inside Detailed see-through radiator intake compartment with front and rear bulkheads, floor treadplate, and fan motor detail Etched-metal radiator exhaust grills with radiator shutters visible underneath Separate radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, early center axle snubbers, sanding lines and brackets (outboard only), and D-77 traction motor and air duct details Retrofitted PTC wheel slip pickups on left side axles 1-3, and right side axles 4-6 Dimensionally accurate truck centers Speed recorder third axle, right side Forward facing handbrake chain mount for Flexicoil trucks Tall jacking pads without holes (intermediate) Sill-mounted EFCO Frame-mounted bell Graham-White (Salem) brand 824-170 and 818-170 primary and secondary centrifugal air filters (accordion-style) Air tanks with fluid drain pipes on sides of fuel tank 4,400 gallon fuel tank with reinforced tank edges where sides meet the tank ends, dual fuel fillers, dual vertical gauges, round gauge on stand and vertical breather pipe Factory-applied wire grab irons, wire lift rings, windshield wipers, trainline hoses with silver gladhands, sand hatch covers, and much more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Printing and lettering legible even under magnification Operates on Code 70, 83 and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DC/DCC & sound ready locomotives also feature: Operable using a DC power pack DCC ready with 21-pin connector

商品重量: 1,320 kg

Angaben zur Produktsicherheit:
Hersteller: Scale Trains, 4901 Old Tasso Road NE Cleveland, TN 37312, USA, www.scaletrains.com
Verantwortlicher Importeur: RD-Hobby Modellbahnen, Jaegersburger Str. 17,68649 Gross-Rohrheim, Deutschland, email@RD-Hobby.de