新商品! 到貨於 二月 2025

預定截止日期：2024/6/24

• 與DCC的使用（DCC接口）

New road numbers Era: 1980s SP Series 8230 to 8299; built 3-7:1980 Fully-assembled Multiple road numbers No truck ground lights (prototype not equipped) LED-Illuminated rectangular walkway lights mounted between front and rear sanding valve doors and round walkway light, aft of raised walkway duct* Equipped with either: LED-illuminated front and rear red LED Pyle-National 17540 “UDE” Gyralites* LED-illuminated front and rear dual LED Pyle-National 20585 (Translite) “Gyralite” signal light* LED-illuminated front and rear stand-off tri-color class lights** Printed number boards with separately controlled backlit LED-illumination* Directional LED headlights Front late SP/UP-style pilot plow with MU hose doors and grab irons Front and rear 3-hose MU hose clusters with silver gladhands Front "tall" stepwells with see-through steps and rear “ladder” steps 88” low short hood with wheel handbrake Bolted battery box doors with wide louvers Late cab sub-base doors with lift-off hinges SP nose headlight package Dash-2 cab with welded side window panels, SP/SSW blue flag bracket, and “L” front window Detailed cab interior with separate floor, rear wall, seats, and standard AAR control stand Original cab front door Sliding cab side windows Standard Mirror mounted fore of cab side windows, both sides Rear cab side vent on left side Standard EMD sunshades and long sunshade tracks Vapor Corp. cab roof HVAC Lost-wax brass Nathan AirChime P24R1 (“P-3”) three-chime horn on clearance bracket; offset to engineer’s side and mounted on number board housing “Whip” radio antenna mounted on ground plane over dust bin Late electrical cabinet "zig-zag" seam, closer to rear of cab Welded ECAFB (late) Late inertial air intake grilles with top and bottom drip rail "Post 1980" extended-range dynamic brake with exhaust silencer Front straight uncoupling levers with loop handles and two inner and two outer mounting brackets Straight rear uncoupling lever with four mounting brackets Handrail set with anticlimber front; inward facing rear end rail mounting brackets and chain Handrail ends and step faces painted white Front and rear 3-hose MU hose clusters with silver gladhands Semi-scale coupler buffer equipped with ScaleTrains.com durable metal semi-scale E Type knuckle couplers Notched pilot faces with high mounted angled lifting slots Pilot-face mounted MU receptacle Front narrow “blunt” front anticlimber rear full-width front pilot anticlimber Scale sectioned treadplate detail on walkways Accurate hood door and long hood detail “Post-1980” exhaust silencer See-through dynamic brake intakes with resistor grid detail See-through standard 48” dynamic brake fan housings with fan blades visible inside Detailed see-through radiator intake compartment with front and rear bulkheads, floor treadplate, and fan motor detail Etched-metal radiator exhaust grills with radiator shutters visible underneath Separate radiator fan grab iron Underbody frame rail with separate plumbing and traction motor cables Detailed HT-C trucks with Hyatt bearing caps, late center axle snubbers, sanding lines and brackets, and D-77 traction motor and air duct details Dimensionally accurate truck centers Speed recorder first axle, left side Forward facing handbrake chain mount for Flexicoil trucks Four-hole SP jacking pads Spare knuckle holders on fuel tank near fuel filler Sill-mounted EFCO Frame-mounted bell Double Graham-White (Prime) brand 975-075 (can style) Standard air tanks 4,400 gallon fuel tank with reinforced tank edges where sides meet the tank ends, dual fuel fillers, dual vertical gauges, round gauge on stand and vertical breather pipe Factory-applied wire grab irons, wire lift rings, windshield wipers, trainline hoses with silver gladhands, sand hatch covers, and much more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Printing and lettering legible even under magnification Operates on Code 70, 83 and 100 rail Packaging safely stores model Minimum radius: 18” Recommended radius: 22” DC/DCC & sound ready locomotives also feature: Operable using a DC power pack DCC ready with 21-pin connector