Neuerscheinung! Auslieferung Juni 2025

• DCC vorbereitet (Schnittstelle vorhanden)

Era: 2017 to Present Series 4043 to 4074, rebuilt 9/17 Road numbers 4071; ex-NS 8824 Horsehead scheme with DC to AC sinewave logo Rebuilt by NS Juniata Shops in Altoona, PA Fully-assembled Multiple road numbers Operating LED-illuminated ground lights on both sides of locomotive* Operating LED-illuminated front and rear deck-mounted alternating ditch lights** Operating LED-illuminated front, rear, and side walkway lights* Printed cab-mounted number boards with separately controlled LED-illumination* Directional LED-illuminated headlights LSL (Locomotive Speed Limiter) indicator lights on cab sides (non-operating) Tall snowplow with MU hose openings and two (2) grab irons Semi-scale GE type coupler buffer equipped with durable metal semi-scale Type E knuckle couplers Inside loop uncoupling levers with down brackets 4-step rear stepwells with see-through steps Walkway with front and rear anticlimbers GE “nub” pattern walkway tread Wide profile end handrails Front high (cab) mounted headlight Nose door without window; security padlock with hasp Two-piece nose top grab irons Battery cabinet access door with latch GE safety cab with four (4) side windows Right side cab under floor access doors: dual large louver panels per door Left side cab under floor access doors: bolted panel forward of the HVAC unit Cab interior with detailed back wall and front dash, high-back seats, conductor’s workstation, and engineer’s AAR-style control stand In-cab grade crossing camera Tinted cab side windows Tall mirror mounted fore and aft of sliding cab side windows on left side, Tall mirror mounted fore of sliding cab side windows on right side; additional small mirror on right side JEM Communications PTC antenna farm with Sinclair antennas Inverter Cabinet with Bolted and hinged access door, top two X panels same size, three lower X panels with 4 - 6 - 4 Bolt Pattern Continuous reinforcement rib under dynamic brake intake grilles High-capacity dynamic brake exhaust (3-port) Rearward right-side air intake grille Left side auxiliary cab: 3 short doors with latches on the #2 door and wide auxiliary cab filter box door Right side auxiliary cab: four (4) doors with latches on #1 and #4 doors Dual triangular lifting bails on top of clean air cab joint Early curved engine cab profile High mounted lift rings on engine cab power assembly doors Three left side door latches and two right door latches on exhaust cab doors Lost-wax brass cast Nathan AirChime K5LAR24 horn mounted on engine cab Early flanged exhaust stack housing “Bathtub” exhaust silencer 22 individually-applied etched metal see-through radiator intake and exhaust grilles on sides and top of radiator compartment Right side late radiator door grilles in alternating heights Right side radiator wing access door with two “T” handles and bolt detail around the door Electronic Handbrake with panel in front of the brake wheel Flat stamped Left rear hood door grille arrangement: tall, short, short grilles High-mounted rear sand fill Early “box” lifting lugs on ends of radiator wings Left side long rail all stanchions early type Right side long rail all stanchions early type Accurately profiled frame with separately-applied plumbing and traction motor cabling GE Hi-Ad trucks with reinforcement plate over center axle on right front and left rear side frames and separately applied brake cylinders, single bracket air plumbing, and rotating bearing caps Rust-color painted wheelsets No speed recorder Dual Graham-White (Salem) 824-100 centrifugal air filters Wabtec 994-500 series air dryer 5,000-gallon fuel tank with vertical wide spaced weld seams Fuel tank detail arrangement (front to back) right side – Fuel filler, EFCO, Digital Fuel Gauge Fuel tank mounted steel bell Separate air tanks with upper mounting brackets Curved handbrake chain bracket Spare coupler knuckle holders on rear pilot face Factory-applied detail parts: wire grab irons, spare knuckles, trainline hoses with silver gladhands, 3-hose MU clusters with silver gladhands, uncoupling levers, windshield wipers, mirrors, sunshades, and more Motor with 5-pole, skew-wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Printing and lettering legible under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum Radius: 18” Recommended Radius: 22” DCC & sound ready locomotives also feature: Operate on DC layouts DCC ready with 21-pin connector