Innovation! Delivery September 2027

• Ready for use with DCC (DCC interface)

New paint scheme Era: 2026 to Present Series 3282 to 3381; built 01/2026 Road numbers 250, 1776, and 2026 Formerly BNSF 3379-3381 Fully-assembled Multiple road numbers LED-illuminated front, rear, and rectangle side walkway lights* LED-illuminated front deck-mounted ditch lights Printed and LED lighted number boards* Semi-scale coupler buffers equipped with die-cast metal semi-scale Type E knuckle couplers, painted a dingy gray/brown color to represent the color of couplers in service Inside loop uncoupling levers with up-down brackets Single trainline hose with silver gladhand Dual front dummy Multiple Unit (MU) receptacles mounted to pilot face Front raised and rear flush pilot-mounted Multiple Unit (MU) receptacles See-through round-hole stepwell steps Walkway with front anticlimber; no support brackets GE “nub” pattern walkway tread Late handrails with U-bolt caps and wide rear-most stanchion on long side Narrow profile end handrails Sand box clean out door with knuckle buster latch Front nose headlight Front straight grab irons mounted directly to the nose Right nose door with window Front high-mounted (cab) numberboard housings Dual cab side blue flag holder Left side under cab front access bolted panel; rear door with square corrugated grille Late cab without barrel bolt latches on subbase doors Detailed cab interior with separate floor, rear wall, seats, and control stand In cab grade crossing camera mounted on right side Tinted cab side windows Tall mirror mounted in front of sliding cab side windows on both sides Switching mirror mounted between rear of sliding cab side windows and fixed rear window on engineer’s side Cab roof with BNSF-specific PTC antenna farm with JEM-manufactured cabinets Inverter Cabinet with Bolted and hinged access door, top two X panels same size, three lower X panels with 4 - 6 - 4 Bolt Pattern See-through dynamic brake exhaust Left side dynamic brake cab: X panel front and dual blower dynamic brake with flush exhaust Etched metal see-through dynamic brake intake grilles with blower motors visible inside Right side dynamic brake cab: X panel door, small grille, door with grille, and door with grille Dynamic brake cab door with low door handle and low-mounted door handle bumper Short right side air intake grille Left side auxiliary cab: 3 tall doors with latches on the #2 door and long auxiliary cab filter box door Right side auxiliary cab: 4 doors with latches on #1 and #4 doors Later production engine cab doors: latched center door in each set of three Four engine cab roof lift rings Lost wax brass cast Nathan AirChime K5HL horn mounted on engine cab roof As-built, rectangular style exhaust stack Left side exhaust cab doors: latched center door in set of three Flush heat exchanger housing with single-piece narrow slot grille Late raised radiator grille 22 individually applied etched metal see-through radiator intake and exhaust grilles on sides and top of radiator compartment Left side radiator cab grille arrangement: Raised doors. Grilles – tall-short-tall-short-tall, no grille under brake wheel, short front angled grille, and two-piece rear angled grille Right side radiator cab grille arrangement: Raised doors. Grilles – tall, short, tall, short, short, tall, short, tall, short front angled grill, two-piece rear angled grille Flat water fill box with sight glass High-mounted horizontal rear headlight Rear wide-spaced dual dummy Multiple Unit (MU) receptacles Accurately profiled frame with separately applied plumbing and cabling GE Hi-Ad trucks with reinforcement plate over center axle on right front and left rear side frames and separately applied brake cylinders, single bracket air plumbing, and rotating bearing caps Wheel faces painted a dingy gray/brown color to represent the color of wheelsets in service Curved handbrake chain bracket Toilet drain with interior handle AEI tag mounted to right sidesill under rear battery box door Dual Graham-White (Prime) finned 075 air filters Graham-White 994-500 air dryer 5,300-gallon fuel tank with internal waste retention tank, vertical fuel gauge, and round fuel gauge Dual fuel fills per side Angled top left side fuel tank top box Long crankcase drainpipe attached to the end of the fuel tank Factory-applied wire grab irons, snowplow with grab irons, spare knuckles, trainline hoses with silver gladhands, 3-hose MU clusters with silver gladhands, uncoupling levers, windshield wipers, mirrors, sunshades, air tanks, fuel tank-mounted electronic bell, brake wheel, and more Motor with 5-pole skew wound armature Dual flywheels All-wheel drive All-wheel electrical pick-up Directional LED headlights Printing and lettering legible under magnification Operates on Code 70, 83, and 100 rail Packaging safely stores model Minimum Radius: 18” Recommended Radius: 22” DCC & sound ready locomotives also feature: Operate using DC DCC ready with 21-pin connector